Leading 10 usual forklift crashes ， forklift procedure need to pay attention to these issues ！.

Do not ignore the forklift at the workplace. If the operation is not good, there will be major mishaps in mins, and there are several crashes entailing forklifts.

Instance 1: The forklift freight obstructed the driver's view, and the individual ahead can not be located, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy products, the employees used their body weight as the counterweight, which almost created casualties.
Instance 3: The size of the forklift freight goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not observe the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift rolls over.
Instance 7: The forklift chauffeur did not wear a safety belt and dropped from the car when it rolled over and was squashed.
Forklift procedure ought to take note of these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and after that begin.
2. For automobiles with hydraulic (air pressure) brakes, the brake hydraulic stress ( atmospheric pressure) gauge should be risk-free prior to beginning.
3. When the forklift starts with a lots, the vehicle driver must first validate that the tons is stable and trustworthy.
4. The start should be slow-moving and constant.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground must be kept at 300mm-400mm, and the pole must be tilted backward. .
2. Do not raise the fork expensive when driving. When getting in and leaving the job site or while driving, beware that there will be no challenges in the sky. When the lots is taking a trip, the fork needs to not be raised too high, which will affect the security of the forklift. .
3. After dumping, the fork needs to be reduced to the normal driving placement prior to driving. .
4. When turning, if there are pedestrians or automobiles nearby, the driving signal ought to be provided initially. High-speed doglegs are banned. High-speed sharp turns will certainly create the automobile to shed lateral security and tip over. .
5. When the forklift is downhill, it is purely forbidden to switch off the fire and slide, and it is forbidden to brake all of a sudden while driving with loads unless there are unique scenarios.
6. When the forklift is running, it needs to obey the web traffic rules in the manufacturing facility and must maintain a certain safety distance from the automobile ahead. .
7. When the forklift is running, the load should be in the lowest setting that does not prevent the driving, and the gantry needs to be properly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the lots have to not obstruct the driver's view. In unique circumstances, when the product influences the forward vision, drive at a low speed when turning around.
9. It is restricted to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving speed of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a low speed when getting in the production workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for personnel to depend on the fork to hold products and play a balancing function. .
12. If problems are found, they will be repaired and reported in a prompt way, and they will never operate with health problems or hide them.

loading and unloading.
1. When fork-loading items, the range between both forks need to be readjusted as needed to make the load of both forks well balanced and not skewed, and one side of the thing should protest the shelf. .
2. It is forbidden to deal with a solitary fork or make use of a fork top or pull. In unique conditions, safety indication must be set up to remind bordering pedestrians. .
3. In the process of loading and discharging products, the forklift should be braked with the brake. .
4. The rate of the lorry need to be slow and stable. Take care not to roll the wheels on the dunnage, so as not to extend the rolled objects and injure Electric Forklift Truck for Warehouse people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the lots, and it ought to be noted that the fork idea should not touch various other products or items. The tons needs to be maintained with minimal back tilt of the gantry to ensure that the tons does not glide in reverse. The pole can be slanted forward slightly when the tons is decreased to enable easy placement of the tons and removal of the forks. .
6. It is forbidden to fork items at broadband and collide with tough objects with the fork head. .
7. When the forklift is working, it is restricted for individuals to loaf the fork, so regarding stay clear of the collapse of the goods and hurt Stand-on Electric Pallet Stacker people. .
8. Straining is prohibited, and it is forbidden to make use of forks to raise employees to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slide, put, round or roll items. .
10. It is not enabled to utilize forks to pick, turn pallet dump.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Prior to leaving the forklift, you should unload the goods or lower the fork frame.
2. Pull the emergency brake deal with to dead or depress the hand brake button.
3. The engine is turned off and the power is removed. (Except for unique scenarios, such as the chauffeur does not leave the vehicle's line of vision and does not surpass 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the appearance needs to be examined, and gas, lubing oil and cooling water must be added.
2. Examine the safety and security performance of starting, running and stopping.
3. Inspect whether the lights and horn signals are full and efficient.
4. Throughout the operation of the forklift, examine whether the pressure and temperature level are typical.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals need to be changed in time.

Forklift Safety Operation Specifications.
1. You must inspect prior to leaving the cars and truck;.
2. When you experience a person before you during driving, you must send out a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not go beyond 5 km/h;.
4. When driving, the low point of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The turning ought to not be as well sharp to stop the propensity of "free turning";.
6. Running up and down the slope must be slow and consistent, and no turning on the incline is enabled.
7. Do not drive throughout the slope. When the gradient is higher than 10%, the automobile needs to be driven in reverse when worsening;.
8. When the forklift personnel carry the goods and progress, if they come across huge or hefty items and go to the motorist's line of sight, they must take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Solitary fork operation is not permitted.
2. It is not permitted to lift the goods for long distance driving.
3. It is not enabled to pick up the goods by turning over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not allowed to make use of inertia force to grab the goods.
6. It is not allowed to utilize stopping force to exile round or easy-to-roll objects.
7. It is not permitted to bring people to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Car parking is not permitted under the following problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal incline more than 5%.
3. When there is an barrier on one side of the roadway, the contrary side of the section with the same size as the barrier need to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844